your one-stop certification solution!
BIS ile ilgili ürünler
Aşağıda BIS belgelendirme Şeması I, ISI Markası Şeması (denetim gereklidir) gerektiren ürünlere genel bir bakış bulacaksınız, ardından BIS kayıt Şeması II, Zorunlu Kayıt Şeması (CRS) (denetim gerekli değildir) gerektiren ürünler için ayrı bir liste bulacaksınız. Ayrıca testlerin gerçekleştirilmesi gereken ilgili IS standartlarını da bulacaksınız.
BIS ile ilgili bileşenlerin bu listeleri büyük olasılıkla genişletilecektir.
BIS sertifikasyonu hakkında daha fazla bilgi için lütfen ücretsiz BIS Sertifikasyonu bilgi kitapçığımızı okuyun.
1. BIS Sertifikasyonu Gerektiren Ürünler (Şema I, ISI İşaret Şeması)
| Sr No. | IS No. | Product |
| Cement (any variety of cement manufactured or sold in India) such as | ||
| 1. | IS 12330 | Sulphate Resisting Portland Cement |
| 2. | IS 12600 | Low heat Portland Cement |
| 3. | IS 1489 (Part 1) | Portland Pozzolana Cement-Part1 Fly-ash based |
| 4. | IS 1489 (Part 2) | Portland Pozzolana Cement-Part 2 Calcined clay based |
| 5. | IS 269 | Ordinary Portland Cement |
| 6. | IS 3466 | Masonry Cement |
| 7. | IS 455 | Portland Slag Cement |
| 8. | IS 6452 | High Alumina Cement for Structural use |
| 9. | IS 6909 | Super sulphated cement |
| 10. | IS 8041 | Rapid hardening Portland cement |
| 11. | IS 8042 | White Portland Cement |
| 12. | IS 8043 | Hydrophobic Portland Cement |
| 13. | IS 8229 | Oil well Cement |
| 14. | IS 16415: 2015 | Composite Cement- Specification. |
| 15. | IS 16993: 2018 | Microfine Ordinary Portland Cement- Specification. |
| 16. | IS 15895: 2018 | High Alumina Refractory Cement. |
| Household Electrical goods | ||
| 17. | IS 12640 (Part 1) | Residual current operated circuit breakers for house hold and similar uses-Part 1 Circuit breakers without integral overcurrent protection (RCCBs) |
| 18. | IS 12640 (Part 2) | Residual current operated circuit breakers for household and similar uses–Part 2 Circuit breakers with integral overcurrent protection(RCVOs) |
| 19. | IS 13010 | AC watt-hour meters, class 0.5, 1 & 2 |
| 20. | IS 13779 | AC static watt-hour meters, class 1 & 2 |
| 21. | IS 14697 | AC static transformer operated watt-hour and VAR-hour meters, class 0.2S & 0.5S |
| 22. | IS 15111 (Part 1 & 2) | Self Ballasted Lamps for General Lighting Services – Part 1 : Safety Requirements & Part 2 : Performance Requirements |
| 23. | IS 302 (Part 2/Sec 3) | Safety of household and similar electrical appliances – Electric iron |
| 24. | IS 302 (Part 2/Sec 201) | Safety of household and similar electrical appliances– Electric immersion water-heaters |
| 25. | IS 302 (Part 2/Sec 202) | Safety of household and similar electrical appliances –Electric stoves |
| 26. | IS 302 (Part 2/Sec 30) | Safety of household and similar electrical appliances-Room heaters |
| 27. | IS 3854 | Switches for domestic and similar purposes |
| 28. | IS 418 | Tungsten filament general service electric lamps (upto100 W ) |
| 29. | IS 694 | PVC insulated cables for working voltages up to and including 1100V |
| 30. | IS 8828 * | Electrical Accessories-Circuit breakers for overcurrent protection for household and similar installations |
| 31. | IS 9968 (Part 1) | Elastomer insulated cables (Part.1): For working voltages up to and including1100 V |
| * Since revised as IS/IEC 60898 | ||
| Batteries | ||
| 32 | IS 8144 | Multi-Purpose dry batteries |
| Food & Related Products | ||
| 33. | IS 15757 | Follow–up formula –complimentary foods |
| 34. | IS 11536 | Processed cereal based complementary foods |
| 35. | IS 1165 | Milk-powder |
| 36. | IS 1166 | Condensed milk, partly skimmed and skimmed condensed milk |
| 37. | IS 12176 | Sweetened ultra high temperature treated condensed milk |
| 38. | IS 13334 (Part 1) | Skimmed milk-powder, standard grade |
| 39. | IS 13334 (Part 2) | Skimmed milk-powder, extra grade |
| 40. | IS 13428 | Packaged Natural Mineral Water |
| 41. | IS 14433 | Infant milk substitutes |
| 42. | IS 17945: 2022 | Food for Special Medical Purpose intended for Infants |
| 43. | IS 14542 | Partly skimmed milk powder |
| 44. | IS 14543 | Packaged Drinking Water (Other than Packaged Natural Mineral Water) |
| 45. | IS 1656 | Milk- cereal Based Complementary foods |
| 46. | IS 14625 | Plastic Feeding Bottles |
| 47. | IS 5168 | Glass Feeding Bottles |
| Oil Pressure Stoves | ||
| 48. | IS 10109 | Oil pressure stove, offset burner type |
| 49. | IS 2787 | Multi-burner oil pressure stoves |
| 50. | IS 1342 | Oil pressure stoves |
| Automobile Accessories | ||
| 51. | IS 13098 | Automotive vehicles –Tubes for pneumatic tyres |
| 52. | IS 15627 | Automotive vehicles– Pneumatic tyres for two and three-wheeled motor vehicles |
| 53. | IS 15633 | Automotive vehicles-Pneumatic tyres for passenger car vehicles– Diagonal and radial ply |
| 54. | IS 15636 | Automotive vehicles- Pneumatic tyres for commercial vehicles-Diagonal and radial ply |
| Cylinder, Valves and Regulator | ||
| 55. | IS 14899 | Liquefied petroleum gas containers for automotive use |
| 56. | IS 15100 | Multifunction valve assembly for permanently fixed liquefied petroleum gas (LPG) containers for automotive use |
| 57. | IS 3196 (Part 4) | Welded low carbon steel cylinders exceeding 5 litre Water capacity for low pressure liquefiable gases Part 4 Cylinders for toxic and corrosive gases |
| 58. | IS 3196 (Part 1) | Welded low carbon steel gas cylinder exceeding 5 litre water capacity for low pressure liquefiable gases Part1 Cylinders for liquefied petroleum gas (LPG) |
| 59. | IS 3196 (Part 2) | Welded low carbon steel gas cylinder exceeding 5-litre water capacity for low pressure liquefiable gases Part 2 Cylinders for liquefiable gases other than LPG. |
| 60. | IS 3224 | Valve fittings for compressed gas cylinder excluding liquefied petroleum gas cylinders |
| 61. | IS 3745 | Yoke Type Valve Connection for Small Medical Gas Cylinders |
| 62. | IS 7142 | Welded low carbon steel cylinders for low pressure liquefiable gases not exceeding 5 litre water capacity |
| 63. | IS 7285 (Part 1) | Refillable Seamless steel gas cylinders Part1 Normalized steel cylinders |
| 64. | IS 7285 (Part 2) | Refillable Seamless steel gas cylinders Part 2 Quenched and tempered steel cylinders with tensile strength less than 1100 MPa (112 kgf/mm2) |
| 65. | IS 7302 | Valve fittings for gas cylinder valves for use with breathing apparatus |
| 66. | IS 7312 | Welded and seamless steel dissolved acetylene gas cylinders |
| 67. | IS 8737 | Valve fittings for use with liquefied petroleum gas cylinders of more than 5 litre water capacity Part 2 Valve fittings for newly manufactured LPG cylinders |
| 68. | IS 8776 | Valve Fittings for Use with Liquefied Petroleum Gas (LPG) Cylinders up to and Including 5-Litre Water Capacity |
| 69. | IS 9798 | Low pressure regulators for use with liquefied petroleum gas (LPG) mixtures |
| Medical Equipment | ||
| 70. | IS 3055 (Part 1) | Clinical thermometers :Part1 Solid stem type |
| 71. | IS 3055 (Part 2) | Clinical thermometers :Part 2 Enclosed scale type |
| 72. | IS 7620 (Part 1) | Diagnostic Medical X-Ray Equipment |
| Steel and Iron Products | ||
| 73. | IS 1785 (Part 1) : 1983 | Plain Hard-drawn Steel Wire For Pre-stressed Concrete: Part 1 Cold Drawn Stress-relieved Wire |
| 74. | IS 1785 (Part 2) : 1983 | Plain hard-drawn steel wire for pre-stressed concrete Part 2: As drawn wire |
| 75. | IS 6003:2010 | Indented wire for Pre-stressed concrete |
| 76. | IS 6006:2014 | Uncoated stress relieved strand for Pre-stressed concrete. |
| 77. | IS 13620:1993 | Fusion bonded epoxy coated reinforcing bars |
| 78. | IS 14268:1995 | Uncoated Stress Relieved Low Relaxation Seven-ply Strand For Pre-stressed Concrete. |
| 79. | IS 277:2003 | Galvanized steel sheets ( plain and corrugated). |
| 80. | IS 2002:2009 | Steel plates for pressure vessels for intermediate and high temperature service including boilers. |
| 81. | IS 2041:2009 | Steel plates for pressure vessels used at moderate and low temperature |
| 82. | IS 2830:2012 | Carbon steel cast billet ingots ,billets, blooms and slabs for rerolling into steel for general structural purpose |
| 83. | IS 1786:2008 | High strength deformed steel bars and wires for concrete reinforcement |
| 84. | IS 648:2006 | Cold rolled non-oriented electrical steel sheets and strip-fully processed type (CRNO) |
| 85. | IS 3024:2015 | Grain oriented electrical steel sheet & strip (CRGO) |
| 86. | IS 15391:2003 | Oriented Electrical Steel Sheet and Strip- Semi-Processed Type- Specification. |
| 87. | IS 2062:2011 | Hot rolled medium and high tensile structural steel |
| 88. | IS 432 : Part 1:1982 | Mild Steel and Medium Tensile Steel Bars and Hard–Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild steel and medium tensile steel bars |
| 89. | IS 432 : Part 2:1982 | Mild steel and Medium Tensile steel bars and Hard–Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard- Drawn Steel Wire |
| 90. | IS 513 (Part-1): 2016 | Cold reduced carbon steel sheets and strips Part 1 Cold Forming and Drawing Purpose |
| 91. | IS 513(Part-2):2016 | Cold reduced carbon steel sheets and strips Part 2 High Tensile and Multi-phase Steel |
| 92. | IS 1079: 2017 | Hot Rolled Carbon Steel Sheet, Plate and Strip — Specification. |
| 93. | IS 1875:1992 | Carbon steel billets, blooms, slabs and bars for forgings. |
| 94. | IS 2879:1998 | Mild steel for metal arc welding electrodes. |
| 95. | IS 3502:2009 | Steel Chequered Plates |
| 96. | IS 5872:1990 | Cold Rolled Steel Strips (Box Strappings). |
| 97. | IS 5986: 2017 | Hot Rolled Steel Sheet, Plate and Strip for Forming and Flanging Purposes — Specification. |
| 98. | IS 6240:2008 | Hot Rolled Steel Plate (up to 6 mm) Sheet and Strip for the Manufacture of Low Pressure Liquefiable Gas Cylinders |
| 99. | IS 7283:1992 | Hot Rolled bars for production of bright bars and machined parts for engineering applications. |
| 100. | IS 7887:1992 | Mild steel wire rods for general engineering purposes. |
| 101. | IS 10748:2004 | Hot Rolled Steel Strip for Welded Tubes and Pipes. |
| 102. | IS 11513:2017 | Hot Rolled Carbon Steel Strip for Cold Rolling Purposes — Specification |
| 103. | IS 15647:2006 | Hot rolled steel narrow width strip for welded tubes and pipes |
| 104. | IS 7904:2017 | High carbon steel wire rods- Specification |
| 105. | IS 14246:2013 | Continuously pre-painted galvanized steel sheets and coils |
| 106. | IS 15965:2012 | Pre-painted aluminium zinc alloy metallic coated steel strip and sheet (Plain). |
| 107. | IS 280: 2006 | Mild steel wire for General Engineering purposes. |
| 108. | IS 1835:1976 | Round Steel wire for ropes |
| 109. | IS 3975:1999 | Low Carbon Galvanized steel wires formed wires and Tapes for armouring of Cables |
| 110. | IS 4368:1967 | Alloy Steel billets, blooms and slabs for forging for general engineering purposes. |
| 111. | IS 4454 (Part 1) : 2001 | Steel wire for mechanical springs Part-1 cold drawn unalloyed steel wire. |
| 112. | IS 4454 (Part 2): 2001 | Steel wire for mechanical springs Part-2 oil hardened and tempered steel wire. |
| 113. | IS 4824:2006 | Bead Wires for Tyres |
| 114. | IS 11169 (Part 1): 1984 | Steels for Cold Heading/Cold extrusion application Part-1 Wrought carbon and low alloy steels |
| 115. | IS 11587:1986 | Structural Weather resistant steel. |
| 116. | IS 15103: 2002 | Fire resistant Steel- Specification |
| 117. | IS 15914:2011 | High Tensile Strength Flat Rolled Steel Plate (Up to 6 mm), Sheet and Strip for the Manufacture of Welded Gas Cylinder. |
| 118. | IS 15961:2012 | Hot Dip aluminium- Zinc alloy metallic coated steel strip and sheet (Plain) |
| 119. | IS 15962:2012 | Structural Steel for Building for Structures with improved seismic Resistance |
| 120. | IS 6527:1995 | Stainless Steel wire Rod |
| 121. | IS 6528:1995 | Stainless Steel Wires |
| 122. | IS 6603:2001 | Stainless Steel Bars and Flats |
| 123. | IS 5522:2014 | Stainless Steel sheets and strips for utensils- Specification |
| 124. | IS 6911:2017 | Stainless Steel Plate, Sheet and Strip- Specification |
| 125. | IS 15997:2012 | Low Nickel Austenitic Stainless Steel Sheet and Strip For Utensils and Kitchen Applications- Specification |
| 126. | IS 1110 : 1990 | Ferrosilicon – Specification |
| 127. | IS 4409 : 1973 | Specification for Ferronickel |
| 128. | IS 1029 : 1970 | Specification for Hot rolled steel strip (bailing) |
| 129. | IS 2385 : 1977 | Specification for Hot-rolled mild steel sheet and strip in coil form for cold-reduced tinplate and cold-reduced black plate |
| 130. | IS 3039 : 1988 | Specification for Structural steel for construction of hulls of ships |
| 131. | IS 9550 2001 | Bright steel bars – v Specification |
| 132. | IS 3748 : 1990 | Tool and die steels – Specification |
| 133. | IS 5517 : 1993 | Steel for hardening and tempering – Specification |
| 134. | IS 7291 : 1981 | Specification for High speed tool steels |
| 135. | IS 7494 : 1981 | Specification for Steel for valves for internal combustion engines |
| 136. | IS 12146 : 1987 | Specification for Carbon manganese steel forgings for pressure vessels |
| 137. | IS 16585 : 2016 | Magnetic materials – specification for individual material – Fe based amorphous strip delivered in the semi-processed state. |
| 138. | IS 2831 : 2012 | Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (ordinary quality) – Specification |
| 139. | IS 1148: 2009 | Steel Rivet Bars (medium And High Tensile) – For Structural Purposes |
| 140. | IS 1673: 1984 | Specification for Mild Steel Wire, Cold Heading Quality |
| 141. | IS 1812: 1982 | Specification for Carbon Steel Wire for the Manufacture of Wood Screws |
| 142. | IS 2507: 1975 | Specification for Cold – rolled Steel Strips For Springs. |
| 143. | IS 2255: 1977 | Specification for Mild Steel Wire Rod for the Manufacture of Machine Screws (By Cold Heading Process). |
| 144. | IS 3195: 1992 | Steel For the Manufacture of Volute And Helical Springs (for Railway Rolling Stock) – Specification . |
| 145. | IS 3431: 1982 | Specification for Steel for the manufacture of volute, helical and laminated springs for automotive suspension. |
| 146. | IS 3885-Part-1: 1992 | Steel for the manufacture of laminated springs (railway rolling stock) Part 1 Flat Sections – Specification. |
| 147. | IS 3885-Part- 2: 1992 | Steel for the manufacture of laminated springs (railway rolling stock) Part 2: Rib and Groove Sections- Specification. |
| 148. | IS 4223: 1975 | Specification for Steel Wire for Umbrella Ribs . |
| 149. | IS 4224: 1972 | Specification for Steel Wire for Staples, Pins And Clips. |
| 150. | IS 4397: 1999 | Cold-rolled Carbon Steel Strips for Ball and Roller Bearing Cages/ Retainers- Specification. |
| 151. | IS 4398: 1994 | Carbon-chromium Steel for the Manufacture of Balls, Rollers and Bearing Races- Specification |
| 152. | IS 6902: 1973 | Specification for Steel Wire for spokes. |
| 153. | IS 6967: 1973 | Specification for Steel For Electrically welded round Link Chains. |
| 154. | IS 7226: 1974 | Specification for Cold rolled medium, high carbon and low alloy steel strip for general engineering purposes. |
| 155. | IS 7557: 1982 | Specification for Steel Wire: (Up to 20 mm) for the manufacture of cold-forged rivets. |
| 156. | IS 8052: 2006 | Steel ingots, billets and blooms for the production of springs, rivets and screws for general engineering applications – Specification. |
| 157. | IS 8951: 2001 | Steel Cast Billet Ingots, Billets and Blooms for production of High Carbon Steel Wire Rods- Specification |
| 158. | IS 8952: 1995 | Steel ingots, blooms and billets for production of mild steel wire rods for general engineering purposes – Specification |
| 159. | IS 9476: 1980 | Specification for Cold rolled steel strips for carbon steel razor blades. |
| 160. | IS 9962: 1981 | Specification for Steel Wire for Needles. |
| 161. | IS 12367:1988 | Specification for Cold-rolled Carbon Steel Strips/ Coils for Manufacture of Welded Tubes. |
| 162. | IS 14331:1995 | Steels for High Temperature Bolting Applications – Specification |
| 163. | IS 14491:1997 | Low carbon high strength cold rolled steel sheets and coils for cold forming- Specification |
| 164. | IS 14650:1999 | Carbon Steel Cast Billet Ingots, Billets, Blooms and Slabs for Rerolling purposes- Specification |
| 165. | IS 4882: 1979 | Specification for Low Carbon Steel Wire for Rivets for use in Bearing Industry |
| 166. | IS 2090:1983 | Specification for High Tensile Steel Bars used in Pre-stressed Concrete |
| 167. | IS 6529:1996 | Stainless Steel Blooms Billets And Slabs For Forging |
| 168. | IS 9294:1979 | Cold-Rolled Stainless Steel Strips for Razor Blades |
| 169. | IS 10631:1983 | Stainless Steel for welding electrode core wire |
| 170. | IS 10632 (Part 2):1983 | Specification for Non Magnetic stainless steel for electrical applications Part 2 Specific requirements for binding wire. |
| 171 | IS 10632 (Part 3):1983 | Specification for Non Magnetic stainless steel for electrical applications Part 3 Specific requirements for sheets, strips and plates. |
| 172 | IS 11169 (Part 2): 1989 | Steels for cold heading/cold extrusion applications – specification Part 2 Stainless steel |
| 173 | IS 5651:1987 | Steels for Pneumatic Tools |
| 174 | IS 9516:1980 | Heat Resisting Steels |
| 175 | IS 11952:1986 | Steels For Piston Pins (Gudgeon Pins) |
| 176 | IS 12045:1987 | Alloys Used in Electrical Resistance Metallic Heating Elements |
| 177 | IS 14652:1999 | 18 Percent Nickel Maraging Steel Bars and Rods |
| 178 | IS 1566:1982 | Specification for Hard-drawn Steel Wire Fabric For Concrete Reinforcement |
| 179 | IS 5489: 1975 | Carburizing Steels For Use in Bearing Industry. |
| 180 | IS 11946:1987 | Soft Magnetic Iron Strips |
| 181 | IS 11947:1987 | Soft Magnetic Iron Rods, Bars Flats and Sections |
| 182 | IS 963: 1958 | Chrome molybdenum steel bars and rods for aircraft purposes |
| 183 | IS 4454 (Part 4): 2001 | Steel Wires for Mechanical Springs- Part 4: Stainless Steel Wire |
| 184. | IS 1993 : 2018 | Cold-reduced Electrolytic Tin Plate |
| 185. | IS 12591:2018 | Cold-reduced Electrolytic Chromium/Chromium oxide – coated steel |
| 186. | IS 412:1975 | Expanded Metal Steel Sheets For General Purposes |
| 187. | IS 2100: 1970 | Steel Billets,Bars And Sections For Boilers |
| 188. | IS 2589: 1975 | Hard Drawn Steel Wire For Upholstery Springs |
| 189. | IS 3298: 1981 | Mild Steel Rivet Bars For Ship Building |
| 190. | IS 4072: 1975 | Steel For Spring Washers |
| 191. | IS 8510 (Part II): 1977 | Steel Wire For Banding Of Armatures And Rotors Part II Specific Requirements for magnetic banding wires |
| 192. | IS 8510 (PartIII): 1977 | Tinned Steel Wire For Banding Of Armatures And Rotors Part III Specific Requirements for non-magnetic banding wires |
| 193. | IS 8563: 1977 | Half Round Mild Steel Wire For The Manufacture of Split Pins |
| 194. | IS 8564: 1977 | Steel Wire For Nipples For Spokes |
| 195. | IS 8565: 1977 | Heald Wire |
| 196. | IS 8566: 1977 | Steel Wire For Reeds |
| 197. | IS 8917: 1978 | Plates For Galvanizing Pots |
| 198. | IS 9442: 1980 | Hot Rolled Steel Plates Sheets And Strips For Manufacture of Agricultural Discs |
| 199. | IS 9485: 1980 | Cold-Reduced And Hot-Rolled Carbon Steel Sheet For Porcelain Enamelling |
| 200. | IS 10794: 1984 | Mild steel wire for cotter pins |
| 201. | IS 12262:1988 | Trapezoidal Steel Wire For Springs Washers |
| 202 | IS 12313: 1988 | Hot-Dip Terne Coated Carbon Steel Sheets |
| 203 | IS 15911:2010 | Structural Steel (Ordinary Quality) |
| 204 | IS 4430: 1979 | Mould Steels |
| 205 | IS 4431: 1978 | Carbon And Carbon- Manganese Free- Cutting Steels |
| 206 | IS 4432: 1988 | Case Hardening Steels |
| 207 | IS 5518: 1996 | Steels For Die Blocks For Drop Forging |
| 208 | IS 8748: 1978 | Forged/Rolled CTC Segments |
| 209 | IS 12145: 1987 | Quenched And Tempered Alloy Steel Forgings For Pressure Vessels |
| 210 | IS 13387: 1992 | Tool Steel Forgings For Metal Forming |
| 211 | IS 14698:1999 | Carbon And Low Alloy Billets, Blooms, Slabs And Bars For Manufacture Of Shell BodiesAnd Proof Shots Used In Defence Services |
| 212 | IS/ISO 11951 : 2016 | Cold – Reduced tinmill products – Blackplate |
| 213 | IS 3930: 1994 | Flame And Induction Hardening Steels |
| 214 | IS 5478: 1969 | Thermostat Metal Sheet and Strip |
| 215 | IS 13352: 1992 | Stock for Forgings produced from Continuously Cast Blooms, Billets and Slabs |
| 216 | IS 16644: 2018 | Stress-Relieved, Low Relaxation Steel Wire for Pre-stressed Concrete |
| 217 | IS 17404 : 2020 | Electrogalvanized Hot Rolled and Cold Reduced Carbon Steel Sheetsand Strips |
| 218. | IS 8329 : 2000 | Centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage |
| 219. | IS 9523:2000 | Ductile iron fittings for pressure pipes for water, gas and sewage |
| 220. | IS 1161:2014 | Steel tubes for structural purposes |
| 221. | IS 1239 (Part 1):2014 | Steel Tubes, Tubulars and Other Wrought Steel Fittings – Part 1 : Steel Tubes |
| 222. | IS 4270:2001 | Steel tubes used for water-wells (upto 200 mm dia) |
| 223. | IS 9139:1979 | Specification for Malleable iron shots and grits for use in foundries |
| Electrical Transformers | ||
| 224. | IS 1180 (Part 1) | Out door type Oil immersed Distribution Transformers upto and including 2500 kVA, 33 KV-specification Part 1 Mineral oil immersed |
| Electrical Motors | ||
| 225. | IS 12615 | Energy Efficient Induction Motors-Three Phase Squirrel Cage |
| Capacitors | ||
| 226. | IS 2993 | A.C. motor capacitors |
| 227. | IS 13340 | Power Capacitors of Self-healing Type for AC Power Systems having Rated Voltage up to 650V |
| 228. | IS 13585 Part 1 | Shunt Power Capacitors of the Non-Self-Healing Type for AC System having a Rated Voltage up to and Including 1000V Part-1 General Performance, Testing amd Rating Safety Requirements Guide for Installation and Operation |
| Chemicals, Fertilizers, Polymers & Textiles | ||
| 229. | IS 252:2013 | Caustic Soda -Specification |
| 230. | IS 10116 : 2015 | Boric Acid – Specification |
| 231. | IS 15573 | Poly Aluminium Chloride |
| 232. | IS 695 | Acetic Acid |
| 233. | IS 2833 | Aniline |
| 234. | IS 517 | Methanol |
| 235. | IS 5158: 1987 | Specification for Phthalic Anhydride, Technical |
| 236. | IS 8058:2018 | Pyridine |
| 237. | IS 16113:2013 | Gamma Picoline |
| 238. | IS 16112:2013 | Beta Picoline |
| 239. | IS 12084: 2018 | Morpholine |
| 240. | IS 297:2001 | Sodium Sulphide, Technical |
| 241. | IS 7129:1992 | Potassium Carbonate, Anhydrous |
| 242. | IS 170:2004 | Acetone |
| 243. | IS 4581:1978 | Phosphorous Trichloride, pure and Analytical Reagent |
| 244. | IS 11744:1986 | Phosphorous Pentachloride, Technical |
| 245. | IS 11657:1986 | Phosphorous Oxychloride, Technical |
| 246. | IS 2080:2021 | Stabilized Hydrogen Peroxide |
| 247. | IS 3205:1984 | Precipitated Barium Carbonate, Technical |
| 248. | IS 12928:1990 | Precipitated Barium for Ceramic and Glass Industry |
| 249. | IS 4505:2015 | Sodium Formaldehyde Sulphoxylate |
| 250. | IS 6100:1984 | Sodium Tripolyphosphate, Anhydrous, Technical |
| 251. | IS 14709:1999 | n- Butyl Acrylate |
| 252. | IS 336:1973 | Ether |
| 253. | IS 5295:1985 | Ethylene Glycol |
| 254. | IS 537:2011 | Toluene |
| 255. | IS 15030:2001 | Terephthalic Acid |
| 256. | IS 14707: 1999 | Methyl Acrylate |
| 257. | IS 14708:1999 | Ethyl Acrylate |
| 258. | IS 12345:1988 | Vinyl Acetate Monomer |
| 259. | IS 4105:2020 | Styrene (Vinyl Benzene) |
| 260. | IS 5149:2020 | Maleic Anhydride, Technical |
| 261. | IS 12540:1988 | Acrylonitrile |
| 262. | IS 17265:2019 | 100 Percent. Polyester Spun Grey and White Yarn (PSY) |
| 263. | IS 17261:2019 | Polyester Continuous Filament Fully Drawn Yarn (FDY) |
| 264. | IS 17264:2019 | Polyester Industrial Yarn (IDY) |
| 265. | IS 17262:2019 | Polyester Partially Oriented Yarn (POY) |
| 266. | IS 17263:2019 | Polyester Staple Fibres (PSF) |
| 267. | IS 7328:2020 | Polyethylene Material for moulding and extrusion |
| 268. | IS 11356:2020 | Styrene-Butadiene Rubber Latex |
| 269. | IS 16481:2016 | Synthetic Micro-Fibres for use in Cement Based Matrix |
| 270. | IS 12795:2020 | Linear Alkyl Benzene |
| 271. | IS 13601:1993 | Ethylene Vinyl Acetate (EVA) Copolymers |
| 272. | IS 7686:2020 | 3(N, N-DiEthyl) Aminophenol |
| 273. | IS 4566:2020 | Methylene Chloride (Dichloromethane) |
| 274. | IS 2012:2006 | Red Phosphorus |
| 275. | IS 17077 :2019/ISO 19062-1 : 2015 | Acrylonitrile Butadiene Styrene (ABS) |
| 276. | IS 869:2020 | Ethylene Dichloride |
| 277. | IS 17370:2020 | p-Xylene |
| 278 | IS 14434:1998 | Polycarbonate |
| 279 | IS 17397 (Part 1) : 2020/ISO 16365-1 : 2014 | Polyurethanes |
| 280 | IS 17442:2020 | Vinyl Chloride Monomer |
| 281 | IS 17450 : 2020 | 1,3 Phenylenediamine |
| 282 | IS 10931 : 1984 | Lauric Acid |
| 283 | IS 12029 : 1986 | Acid Oil |
| 284 | IS 12067: 1987 | Palm Fatty Acids |
| 285 | IS 12068 :1987 | Rice Bran Fatty Acids |
| 286 | IS 12069 : 1987 | Coconut Fatty Acids |
| 287 | IS 12124 : 1987 | Rubberseed Fatty Acids |
| 288 | IS 12361 :1988 | Hydrogenated Rice Bran Fatty Acids |
| Kitchen Appliances | ||
| 289. | IS 302 (Part 2/ Section 14) | Hand-held Blender |
| 290. | IS 4250 | Domestic Electric Food Mixer (Liquidizers and Grinders) and Centrifugal Juicer |
| Domestic Water Heaters for use with LPG | ||
| 291. | IS 15558 | Instantaneous Domestic Water Heater for use with Liquefied Petroleum Gas |
| Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls | ||
| 292. | IS 1391 (Part-1): 2017 | Room Air Conditioners- Specification Part 1 Unitary Air Conditioners |
| 293. | IS 1391 (Part-2): 2018 | Room Air Conditioners- Specification Part 2 Split Air Conditioners |
| 294. | IS 8148:2018 | Ducted and Package Air Conditioners |
| 295. | IS 11329:2018 | Finned type Heat Exchanger for Room Air Conditioner |
| 296. | IS 10617:2018 | Hermetic compressor , Hermetic Compressors-Specification |
| Plugs and Socket-Outlets and Alternating Current Direct Connected Static Prepayment Meters for Active Energy | ||
| 297. | IS 1293 : 2005 | Plugs and socket-outlets of Rated Voltage up to and including 250 Volts and Rated current up to and including 16 amperes |
| 298. | IS 15884:2010 | Alternating Current Direct Connected Static Prepayment Meters for Active Energy (Class1 and 2) |
| Domestic Gas Stoves for use with Liquefied Petroleum Gases | ||
| 299. | IS 4246: 2002 | Domestic Gas Stoves for use with Liquefied Petroleum Gases |
| Transparent Float Glass | ||
| 300. | IS 14900: 2018 | Transparent Float Glass |
| Domestic Pressure Cooker | ||
| 301. | IS 2347:2017 | Domestic Pressure Cooker |
| Cables | ||
| 302. | IS 1554(Part 1) : 1988 | Specification for PVC Insulated (Heavy Duty) Electric Cables Part 1 For Working Voltages up to and Including 1100 V |
| 303. | IS 1554(Part 2) : 1988 | Specification for PVC Insulated (Heavy Duty) Electric Cables Part 2 For Working Voltages from 3.3 kV up to and Including 11 kV |
| 304. | IS 7098 (Part 1) : 1988 | Specification for Crosslinked Polyethylene Insulated PVC Sheathed Cables Part 1 for working voltages up to and including 1100 V |
| 305. | IS 7098 (Part 2) : 2011 | Crosslinked polyethylene insulated Thermoplastics sheathed cables – Specification Part 2 for working voltages from 3.3 kV up to and including 33 kV |
| 306. | IS 7098 (Part 3) : 1993 | Cross-Linked Polyethylene Insulated Thermoplastics Sheathed Cables Part 3 For Working Voltages from 66 kV Up to and Including 220 kV |
| 307. | IS 14255 : 1995 | Aerial Bunched Cables – For Working Voltages Up to and Including 1100 Volts – Specification |
| 308. | IS 9968 (Part 2) : 2002 | Specification for Elastomer Insulated Cables Part 2 For Working Voltages form 3.3 kV Up to and Including 33 kV |
| 309. | IS 8784 : 1987 | Specification for Thermocouple Compensating Cables |
| 310. | IS 9857 : 1990 | Welding Cables – Specification |
| 311. | IS 14494 : 2019 | Elastomer Insulated Flexible Cables for Use in Mines – Specification |
| 312 | IS 2593 : 1984 | Specification for Flexible Cables for Miner’s Cap-Lamps |
| 313. | IS 5950 : 1984 | Specification for Shot Firing Cables (for use other than in shafts) |
| 314. | IS 17048 : 2018 | Halogen Free Flame Retardant (HFFR) Cables for Working Voltages Up to and Including 1100 V – Specification |
| Rubber Hose for Liquefied Petroleum Gas (LPG) | ||
| 315. | IS 9573(Part 1):2017 | Rubber Hose for Liquefied Petroleum Gas (LPG)- Specification Part 1 Industrial Application |
| 316. | IS 9573(Part 2):2017 | Rubber Hose for Liquefied Petroleum Gas (LPG)- Specification Part 2- Domestic and Commercial Application. |
| Aluminium Foil | ||
| 317. | IS 15392 | Aluminium and Aluminium Alloy Bare Foil for Food Packaging |
| Non Electric Toys | ||
| 318. | IS 9873 (Part 1) : 2018 | Safety of Toys Part l Safety Aspects Related to Mechanical and Physical Properties. |
| IS 9873 (Part 2) : 2017 | Safety of Toys Part 2 Flammability. | |
| IS 9873 (Part 3) : 2017 | Safety Requirements for Toys Part 3 Migration of Certain Elements. | |
| IS 9873 (Part 4) : 2017 | Safety of Toys Part 4 Swings, Slides and Similar Activity Toys for Indoor and Outdoor Family Domestic Use. | |
| IS 9873 (Part 7) : 2017 | Safety of Toys Part 7 Requirements and Test Methods for Finger Paints. | |
| IS 9873 (Part 9) : 2017 | Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children’s Products. | |
| Electric Toys | ||
| 319. | IS 15644: 2006 | Safety of Electric Toys. |
| Flat Transparent Sheet Glass | ||
| 320. | IS 2835 : 1987 | Flat Transparent Sheet Glass. |
| Safety Glass | ||
| 321. | IS 2553 (Part 1):2018 | Safety Glass -Specification Part 1 Architectural, Building and General uses. |
| 322. | IS 2553 (Part 2):2019 | Safety Glass -Specification Part 2 For Road Transport . |
| Woven Sacks | ||
| 323. | IS 14887:2014 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging of 50 kilogram Foodgrains |
| 324. | IS 16208:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging 10 kilogram, 15 kilogram, 20 kilogram, 25 kilogram, and 30 kilogram Foodgrains |
| 325. | IS 14968:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for packaging 50 kilogram /25 kilogram Sugar |
| 326. | IS 14252:2015 | Textiles –High Density Polyethylene (HDPE)/ Polypropylene (PP) Woven Sacks for filling Sand |
| Butterfly Valves | ||
| 327. | IS 13095:1991 | Butterfly valves for general purpose |
| Reflectors for Bicycles | ||
| 328. | IS/ISO 6742-2:2015 | Retro-reflective Devices |
| Paper | ||
| 329. | IS 14490:2018 | Plain Copier Paper |
| Cattle Feeds | ||
| 330. | IS 2052 : 2009 | Compounded Feeds for Cattle |
| Automobile Wheel Rim Component | ||
| 331. | IS: 16192 (Part 1) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 1 Light Alloy Wheel Rims Method of Tests and Requirements |
| 332. | IS: 16192 (Part 2) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 2 Sheet Metal Wheel Rims Method of Tests and Requirements |
| 333. | IS: 16192 (Part 3) | Automotive Vehicles Wheel Rims for Two and Three Wheeled Vehicles Part 3 Spoke Wheel Rims Method of Tests and Requirements |
| 334. | IS: 9436 | Performance Requirements and Methods of Tests for Wheels for Passenger Cars |
| 335. | IS: 9438 | Performance Requirements and Methods of Tests for Wheels or Rims for Trucks and Buses |
| Foot Wear | ||
| 336. | IS 5557: 2004 | Industrial and protective rubber knee and ankle boots |
| 337. | IS 5557 (Part 2): 2018 | All rubber gum boots and ankle boots |
| 338. | IS 5676: 1995 | Moulded solid rubber soles and heels |
| 339. | IS 6664: 1992 | Rubber microcellular sheets for soles and heels |
| 340. | IS 6719: 1972 | Solid PVC soles and heels |
| 341. | IS 6721: 1972 | PVC sandal |
| 342. | IS 10702: 1992 | Rubber Hawai Chappal |
| 343. | IS 11544: 1986 | Slipper, rubber |
| 344. | IS 12254: 1993 | Polyvinyl chloride(PVC) industrial boots |
| 345. | IS 13893: 1994 | Polyurethane sole, semirigid |
| 346. | IS 13995: 1995 | Unlined moulded rubber boots |
| 347. | IS 16645: 2018 | Moulded plastics footwear- Lined or Unlined polyurethane boots for general industrial use |
| 348. | IS 16994: 2018 | Footwear for men and women for municipal scavenging work |
| 349. | IS 1989 (Part 1): 1986 | Leather safety boots and shoes for miners |
| 350. | IS 1989 (Part.2): 1986 | Leather safety boots and shoes for heavy metal industries |
| 351. | IS 3735: 1996 | Canvas Shoes Rubber Sole |
| 352. | IS 3736: 1995 | Canvas Boots Rubber Sole |
| 353. | IS 3976: 2018 | Safety Rubber Canvas Boots for Miners |
| 354. | IS 11226: 1993 | Leather safety footwear having direct moulded rubber sole |
| 355. | IS 14544: 1998 | Leather safety footwear with direct moulded polyvinyl chloride (PVC) sole |
| 356. | IS 15844: 2010 | Sports footwear |
| 357. | IS 17012: 2018 | High ankle tactical boots with PU – Rubber sole |
| 358. | IS 17037: 2018 | Antiriot shoes |
| 359. | IS 17043: 2018 | Derby shoes |
| 360. | IS 15298 (Part 2): 2016 | Personal protective equipment – Part 2 Safety Footwear |
| 361. | IS 15298 ( Part 3) : 2019 | Personal protective equipment – Part 3 Protective Footwear |
| 362. | IS 15298 (Part 4) : 2017 | Personal protective equipment – Part 4 Occupational Footwear |
| Press Tool-Punches | ||
| 363. | IS 4296 (Part 1):2016 | Tools for Pressing Part 1 Round Punches with 60 Degrees Conical Head and Straight Shank |
| 364. | IS 4296 (Part 2):2016 | Tools for Pressing Part 2 Punches with Cylindrical Head and Straight or Reduced Shank |
| 365. | IS 4296 (Part 3):2016 | Tools for Pressing Part 3 Round Punches with 60 Degrees Conical Head and Reduced Shank |
| Helmet for riders of Two Wheeler Motor Vehicles | ||
| 366. | IS 4151: 2015 | Helmet for riders of Two Wheeler Motor Vehicles |
| Refrigerating Appliances | ||
| 367. | IS 17550 (Part 1): 2021 | Household Refrigerating Appliances- Characteristics and Test Methods part-1 General Requirements |
| 368. | IS 7872: 2018 | Freezers |
| Centrifugally cast (Spun) iron pipes | ||
| 369. | IS 1536: 2001 | Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage |
| 370. | IS 3989: 2009 | Centrifugally cast (Spun) iron spigot and socket soil, waste, ventilating and rainwater pipes, fittings and accessories |
| 371. | IS 15905: 2011 | Hubless centrifugally cast (Spun) iron pipes, fittings and accessories – Spigot series |
| Flux Cored (Tubular) Electrodes | ||
| 372. | IS 15769:2008 | Flux Cored (Tubular) Electrodes for Gas Shielded and Self-Shielded Metal Welding of Carbon or Carbon- Manganese Steel |
| Sewing Machine | ||
| 373. | IS 15449 : Part 1 : 2004 | Household Zig-Zag Sewing Machine Head |
| Water Treatment System | ||
| 374. | IS 16240 : 2015 | Reverse Osmosis (RO) Based Point-Of-Use (POU) Water Treatment System |
| Jute Bag | ||
| 375. | IS 1943:1995 | A- twill Jute Bag |
| 376. | IS 2566:1993 | B-twill Jute bags for packing foodgrains |
| 377. | IS 12650:2018 | Jute bags for packing 50 Kg foodgrains |
| 378. | IS 15138:2010 | Jute bags for packing 50 Kg sugar |
| 379. | IS 16186:2014 | Light weight jute sacking bags for packing 50 Kg foodgrains |
| 380. | IS 16372:2015 | Jute bags for packing up to 30 Kg foodgrains |
| 381. | IS 17266:2019 | Viscose Staple Fibres |
| 382. | IS 15351 : 2015 | Laminated High Density Polyethylene (HDPE) Woven Geomembrane for Water Proof Lining |
| 383. | IS 15909 : 2020 | Poly Vinyl Chloride (PVC) Geomembranes |
| 384. | IS 16653 : 2017 | Needle punched non-woven geobags |
| 385. | IS 16654: 2017 | Polypropylene Multifilament woven geobags |
| 386. | IS 14715 (Part 1): 2016 | Jute Geotextiles |
| 387. | IS 14715 (Part 2): 2016 | Jute Geotextiles |
| 388. | IS 15869 : 2020 | Open Weave Coir Bhoovastra |
| 389. | IS 16391 : 2015 | Geotextiles used in sub-grade separation in pavement structures |
| 390. | IS 16393 : 2015 | Geotextiles used in Subsurface Drainage Application |
| 391. | IS 16362 : 2020 | Geotextiles used in Sub-grade Stabilisation in pavement structures |
| 392. | IS 16352 : 2020 | High Density Polyethylene (HDPE) Geomembranes for lining |
| 393. | IS 16090:2013 | Geotextiles used as protection (or cushioning) materials |
| 394. | IS 16392:2015 | Geotextiles for permanent erosion control in hard armor systems |
| 395. | IS 17371:2020 | Geogrids for flexible pavements |
| 396. | IS 17372:2020 | Polymeric strip or geostrip used as soil reinforcement in retaining structures |
| 397. | IS 17373:2020 | Geogrids used in reinforced soil retaining structures |
| 398. | IS 17374:2020 | Reinforced HDPE membrane for effluents and chemical resistance lining |
| 399. | IS 17483 (Part 1): 2020 | Geocells |
| 400. | IS 17483 (Part 2): 2020 | Geocells |
| 401. | IS 15741 : 2007 | Curtains and Drapes |
| 402. | IS 15768 : 2008 | Upholstered composites used for non-domestic furniture |
| 403. | IS 16890 : 2018 | Protective clothing for firefighters |
| 404. | IS 16874 : 2018 | Protective gloves for firefighters |
| 405. | IS 15748 : 2022 | Protective clothing for industrial workers exposed to heat |
| 406. | IS 15742 : 2007 | Clothing made of limited flame spread materials and material assemblies affording protection against heat and flame |
| 407. | IS 15809 : 2017 | High visibility Warning Clothes |
| 408. | IS 16655 : 2017 | Protective Clothing for use in welding and allied processes |
| 409. | IS 16725 : 2018 | Tactical 3 point sling |
| 410. | IS 16726 : 2018 | Pouch for ammunition and grenades made of disruptive pattern nylon-66 |
| 411. | IS 17051 : 2018 | Bullet resistant jackets |
| 412. | IS 17286 : 2019 | Water-proof multipurpose rain poncho |
2. BIS Kaydı Gerektiren Ürünler (Şema II, Zorunlu Kayıt Şeması (CRS))
| I. List of Electronics and IT Goods under ‘Compulsory Registration Scheme’ for Self Declaration of conformity-Notified by Ministry Of Electronics And Information Technology | |||
| Sl. No. | IS No. | Title | Product Category |
| 1. | IS 616 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Electronic Games (Video) |
| 2. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Laptop/Notebook/Tablets |
| 3. | IS 616 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Plasma/ LCD/LED Televisions of screen size 32″ & above |
| 4. | IS 616 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Optical Disc Players with built in amplifiers of input power 200W and above |
| 5. | IS 302-2-25 | Safety of household and similar electrical appliances: Part 2 Particular requirements: Section 25 Microwave ovens | Microwave Ovens |
| 6. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Visual Display Units, Video Monitors of screen size 32″ & above |
| 7. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Printers, Plotters |
| 8. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Scanners |
| 9. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Wireless Keyboards |
| 10. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Telephone Answering Machines |
| 11. | IS 616 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Amplifiers with input power 2000W and above |
| 12. | IS 616 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Electronic Musical Systems with input power 200W and above |
| 13. | IS 302-2:26 | Safety of household and similar electrical appliances: Part 2 Particular requirements: Section 26 Clocks | Electronic Clocks with Mains Powers |
| 14. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Set Top Box |
| 15. | IS 13252 (Part 1) | Information Technology Equipment – Safety – General Requirements | Automatic Data Processing Machine |
| 16. | IS 13252 (Part 1) | Information Technology Equipment- Safety General Requirements | Power Adaptors for IT Equipments |
| 17. | IS 616 | Audio, Video and Similar Electronic Apparatus-Safety Requirements | Power Adaptors for Audio, Video & Similar Electronic Apparatus |
| 18. | IS 16242 (Part 1) | General and Safety Requirements for UPS | UPS/Invertors of rating≤5kVA |
| 19. | IS 15885 (Part 2/Sec 13) | Safety of Lamp Control gear Part 2 Particular Requirements Section 13 d.c. or a.c. Supplied Electronic Control gear for LED Modules | DC or AC Supplied Electronic Control gear for LED Modules |
| 20. | IS 16046 | Secondary Cells and Batteries containing Alkaline or other non-acid Electrolytes-Safety Requirements for Portable sealed secondary cells, and for Batteries made from them for use in portable applications | Sealed Secondary Cells/Batteries containing Alkaline or other non-acid Electrolytes for use in portable applications |
| 21. | IS 16102(Part 1) | Self-Ballasted LED Lamps for General Lighting Services Part 1 Safety Requirements | Self-Ballasted LED Lamps for General Lighting Services |
| 22. | 10322 (Part 5/Sec 1) | Luminaries Part 5 Particular Requirements Sec 1 Fixed General purpose luminaries | Fixed General Purpose LED Luminaries |
| 23. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Mobile Phones |
| 24. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Cash Registers |
| 25. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Point of Sale Terminals |
| 26. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Copying Machines/Duplicators |
| 27. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Smart Card Readers |
| 28. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Mail Processing Machines/Postage Machines/Franking Machines |
| 29. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Passport Reader |
| 30. | IS 13252 (Part 1) | Information Technology Equipment-Safety-General Requirements | Power Banks for use in portable applications |
| 31. | IS 16333 (Part-3) | Mobile Phone Handsets Part 3 Indian Language Support for Mobile Phone Handsets – Specific Requirements | Mobile Phones |
| 32. | IS 10322 (Part 5/Section 2): 2012 | Luminaires Part 5: Particular Requirements Section 2 Recessed Luminaires | Recessed LED Luminaries |
| 33. | IS 10322 (Part 5/Section 3): 2012 | Luminaires – Part 5: Particular Requirements Section 3 Luminaires for Road and Street Lighting | LED Luminaires for Road and Street lighting |
| 34. | IS 10322 (Part 5/Section 5): 2013 | Luminaires – Part 5: Particular Requirements Section 5 Flood Lights | LED Flood Lights |
| 35. | IS 10322 (Part 5/Section 6): 2013 | Luminaires – Part 5: Particular Requirements Section 6 Hamp Lamps | LED Hand lamps |
| 36. | IS 10322 (Part 5/Section 7): 2013 | Luminaires – Part 5: Particular Requirements Section 7 Lighting Chains | LED Lighting Chains |
| 37. | IS 10322 (Part 5/Section 8): 2013 | Luminaires – Part 5: Particular Requirements Section 8 Luminaires for Emergency Lighting | LED Luminaires for Emergency Lighting |
| 38. | IS 16242 (Part 1):2014 | General and Safety Requirements for UPS | UPS/Inverters of rating ≤ 10kVA |
| 39. | IS 616:2010 | Audio, Video and Similar Electronic Apparatus – Safety Requirements | Plasma/ LCD/LED Television of screen size up-to 32” |
| 40. | IS 13252 (Part 1):2010 | Information Technology Equipment –Safety General Requirements | Visual Display Units, Video Monitors of screen size up-to 32” |
| 41. | IS 13252 (Part 1):2010 | Information Technology Equipment –Safety General Requirements | CCTV Cameras/CCTV Recorders |
| 42. | IS 302 (Part 1): 2008 | Safety of Household and similar electrical appliances Part 1 General requirements | Adapters for household and similar electrical appliances |
| 43. | IS 13252 (Part 1):2010 | Information Technology Equipment –Safety General Requirements | USB driven Barcode readers, barcode scanners, Iris scanners, Optical fingerprint scanners |
| 44. | IS 13252 (Part 1):2010 | Information Technology Equipment –Safety General Requirements | Smart watches |
| 45. | IS 16103 (Part 1): 2012 | LED modules for general lighting: Part 1 safety requirements | Standalone LED Modules for General Lighting |
| 46. | IS 10322 (Part 5)Section 9: 2017 | Luminaries: Part 5 Particular Requirements Section 9 Rope Lights | Lighting Chain (Rope Lights) |
| 47. | IS 13252 (Part 1) :2010 | Information technology equipment – safety part 1 general requirements | Keyboard |
| 48. | IS 302 (Part 2): Section 6: 2009 | Safety of household and similar electrical appliances: part 2 particular requirements, section 6 cooking ranges, hobs, ovens and similar appliances | Induction Stove |
| 49. | IS 13252 (Part 1) :2010 | Information technology equipment – safety part 1 general requirements | Automatic Teller Cash dispensing machines |
| 50. | IS 13252 (Part 1) :2010 | Information technology equipment – safety part 1 general requirements | USB Type External Hard Disk Drive |
| 51. | IS 616: 2017 | Audio, video and similar electronic apparatus-safety requirements | Wireless Headphone and Earphone |
| 52. | IS 13252 (Part 1) :2010 | Information technology equipment – safety part 1 general requirements | USB Type External Solid- State Storage Devices (above 256 GB capacity) |
| 53. | IS 616: 2017 | Audio, video and similar electronic apparatus-safety requirements | Electronic Musical System with input power below 200 Watts |
| 54. | IS 13252 (Part 1) :2010 | Information technology equipment – safety part 1 general requirements | Standalone Switch Mode Power Supplies (SMPS)with output voltage 48 V (max) |
| 55. | IS 616: 2017 | Audio, video and similar electronic apparatus-safety requirements | Television other than Plasma/ LCD/LED TVs |
| 56. | IS 302 (Part 2): Section 15: 2009 | safety of household and similar electrical appliances: part 2 particular requirements: section 15 appliances for heating liquids | Rice Cooker |
| 57. | IS 616:2017 | Audio, video and similar electronic apparatus-safety requirements | Wireless microphone |
| 58. | IS 13252 (Part 1): 2010 | Information technology equipment – safety part 1 general requirements | Digital Camera |
| 59. | IS 616:2017 | Audio, video and similar electronic apparatus-safety requirements | Video Camera |
| 60. | IS 616:2017 | Audio, video and similar electronic apparatus-safety requirements | Webcam (Finished Product) |
| 61. | IS 616:2017 | Audio, video and similar electronic apparatus-safety requirements | Smart Speakers (with and without Display) |
| 62. | IS 60669-2-1: 2008 | Particular requirements for Electronic switches standards for Switches for household and similar fixed electrical installations. | Dimmers for LED products |
| 63. | IS 616:2017 | Audio, video and similar electronic apparatus-safety requirements. | Bluetooth speakers |
| 64. | IS 18112:2022 | Digital Television Receiver for Satellite Broadcast Transmission – Specification | Television Sets |
| II. List of Solar Photovoltaics, Systems, Devices and Components under Compulsory Registration Scheme- Notified by Ministry Of New and Renewable Energy | |||
| Sl. No. | IS No. | Title | Product Category |
| 1. | IS 14286 IS/IEC 61730 -1 IS/IEC 61730 -2 | Crystalline Silicon Terrestrial Photovoltaic (PV) modules – Design Qualification And Type Approval | Crystalline Silicon Terrestrial Photovoltaic (PV) modules (Si wafer based) |
| 2. | IS 16077 IS/IEC 61730 -1 IS/IEC 61730 -2 | Thin-Film Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval | Thin-Film Terrestrial Photovoltaic (PV) Modules (a-Si, CiGs and CdTe) |
| 3. | IS 16221 (Part 2) | Safety of Power Converters for Use in Photovoltaic Power Systems Part 2-Particular Requirements for Inverters | Power converters for use in photovoltaic power system |
| 4. | IS 16169 | Test Procedure of Islanding Prevention Measures for Utility-Interconnected Photovoltaic Inverters | Utility –Interconnected Photovoltaic inverters |
| 5. | IS 16270 | Secondary Cells and Batteries for Solar Photovoltaic Application General-Requirements and Methods of Test | Storage battery |
| III. List of chemicals notified by Ministry of Chemicals and Fertilizers. | |||
| Sl. No. | IS No. | Title | Product Category |
| 1. | IS 798:2020 | Ortho Phosphoric Acid – Specification | Ortho Phosphoric Acid |
| 2. | IS 17439:2020 | Polyphosphoric Acid – Specification | Polyphosphoric Acid |
| 3. | IS 17412:2020 | Trimethyl Phosphite – Technical Grade | Trimethyl Phosphite |
| IV. List of Textile material notified by Ministry of Textiles | |||
| Sl. No. | IS No. | Title | Product Category |
| 1. | IS 12171:2019 | Cotton Bales- Specification | Cotton Bales |
3. BIS Sertifikasyonu Gerektiren Ürünler (Scheme X)
| S. No. | IS Standard | Product | Date of Implementation |
| 1. | IS 60947-2 | Circuit-breakers | May 10th, 2024 |
| 2. | IS 60947-3 | Switches, disconnectors, switch disconnectors and fuse-combination units | May 10th, 2024 |
| 3. | IS 60947-4-1 | Contactors and motor-starters, electromechanical contactors, and motor | May 10th, 2024 |
| 4. | IS 60947-4-2 | Contactors and motor-starters, AC semiconductor motor controllers and starters | May 10th, 2024 |
| 5. | IS 60947-4-3 | Contactors and motor-starters, AC semiconductor motor controllers and contactors for non-motor loads | May 10th, 2024 |
| 6. | IS 60947-5-1 | Control circuit devices and switching elements, electromechanical control circuit devices | May 10th, 2024 |
| 7. | IS 60947-5-2 | Control circuit devices and switching elements, proximity switches | May 10th, 2024 |
| 8. | IS 60947-5-3 | Control circuit devices and switching elements, electrical emergency stop devices with mechanical latching function | May 10th, 2024 |
Bize ulaşın!
MPR India Certification – uzman danışmanlık ve dünya çapında sertifikasyon projelerinin uygulanması.
